StopTech Sport Slotted Front Brake Rotors for Scion FR-S / Subaru BRZ 126.47021SL & 126.47021R

1. StopTech Sport Slotted Front Brake Rotors for Scion FR-S/ Subaru BRZ are specifically designed to run cooler. 

2. If has superior metallurgy and design specifications including vane designs to further promote cooler running temperatures. 

3. Venting the gas emitted by hot brake pads improves overall brake performance and helps minimize fade. 

4. StopTech Sport Slotted Front Brake Rotors will improve wet and dry brake performance and is a safer alternative to drilling crack prone holes through cast iron rotors.

5. The slotting process removes far less of the rotor's surface area than conventional cross drilling. This will help maintain the highest friction of coefficient for the brake pads against increasing initial "bite." 

6: Slotted rotors trade only 3.7% of their surface area to the slots that vent the gasses, while drilled rotors sacrifice up to 7. 75% of their surface area.

7. Less surface area means less stopping friction. The rotors are also double disc ground and mill balanced to ensure a consistent friction surface and improved pad bed-in.

8. StopTech Sport Slotted Front Brake Rotors undergone Electro coating (E-coating) finish, an electrostatic applied finish is designed to withstand 400 hours of saltwater exposure without rusting and provides long lasting corrosion protection in the critical hat and cooling vane areas.

 **NOT FOR FACTORY BREMBO EQUIPPED VEHICLES**

Additional E-Coating Advantages:

• Uniform coating thickness over all areas including sharp corners, recesses and areas that would be hard to reach with spray painting
• Paint material is water-based and nontoxic
• Approximately 95% utilization of paint with no overspray, drip or drain losses
• Complete paint coverage — no touchup ever required

9. These specific rotors' increased molybdenum (higher carbon) content further that extends reliability, longevity and helps reduce NVH "noise" issues.

10. Designed to beat the challenges of high performance driving and severe duty brake demands as well as to enhance open wheel designs.

12. All  StopTech Sport Slotted Front Brake Rotors represent one of the most cost-efficient performance brake upgrades offered in the market today.

StopTech Sport Slotted Front Brake Rotors for Scion FR-S / Subaru BRZ 126.47021SL & 126.47021R

GRUPPEM RAM AIR SYSTEM FOR PORSCHE 911 997 FR-0141

GRUPPEM RAM AIR SYSTEM FOR PORSCHE 911 997 FR-0141

1. Gruppem had engineered carbon duct that completely block the hot air in the engine room. 

2. Fresh air is directly introduced to lower and stabilize the intake air temperature. 

3. Shown great torque and power-up in the entire range from low to high revs. 

4. The high quality material gives a real sporty intake sound. 

5. Installation is bolt-on only with a dedicated fitting adapter. 

Manufacturer: GruppeM 
Brand: GroupM GruppeM 
Code: 997 
Displacement: 3.6 LITER 
Grade / Specifications: GT3 Previous term

GRUPPEM RAM AIR SYSTEM FOR PORSCHE 911 997 FR-0141

 

C&R Racing Porsche 981 GT4 16 42mm Center Radiator cr20-05052

1. This is the same radiator used by the winning 2016 Sebring and Laguna Seca team.

2. This is a must have radiator for great performance upgrade on your 2016 Porsche GT4. 

3. C&R Performance offers radiators for the Porsche 981 GT4 built by PWR in Australia and used by top teams in The IMSA Continental Tire GS series. 

4. The center radiator featured 42mm dimple tube core technology for exceptionally unmatched heat rejection. 

5. The radiator mounts is the same as OEM mounting for ease of installation.

6. This C&R radiator will gives optimum cooling for Porsche 981 GT4 on the IMSA circuit or at any other circuits. 

7. This center radiator fits 981 GT4 race car only

C&R Racing Porsche 981 GT4 16 42mm Center Radiator cr20-05052

 

VR Aero Carbon Fiber Side Air Ducts Porsche 991 Turbo VR-991TT-650

1. VR Aero had introduced  these stylish carbon fiber side air ducts that fit Porsche 991 turbo stock pieces.  

2. The side air ducts are finished in a 2x2 carbon weave with a high gloss clear coat. 

Features:

• Carbon Fiber
• 2x2 Carbon weave
• Gloss Finish
• 3K UV resistant
• Perfect Fitment
• Added Exterior Styling
• Fits over stock ducts for easy install

Fitment:

• Porsche 991 Turbo 14-19

VR Aero Carbon Fiber Side Air Ducts Porsche 991 Turbo VR-991TT-650

 

Radium Engineering Dual Catch Can Kit S197 Shelby GT500 Fluid Lock rad20-0329-FL

1. Compatible with the 2010-2014 Shelby GT500 (S197). 

2. No permanent modifications to the vehicle are required.

3. An oil catch can is essential on a performance vehicle to protect the engine from elevated levels of crankcase blow-by oil accumulation from high performance driving. 

4. Excess oil saturated air circulating back into the air intake stream can lead to degraded performance. 

5. Closed loop systems remove the oil and sludge from the PCV gasses before it is routed to the engine to be burned.

6. A closed loop system also promotes negative crankcase pressure for optimal performance. 

7. Furthermore, closed systems prevent unwanted oil vapors from entering the cabin. 

8. The dipsticks built into the catch cans allow easy inspection of accumulated fluid. 

9. This kit mounts using factory holes on the chassis and integrate perfectly with the surrounding components. 

10. These two oil catch cans (PCV side and Crankcase side) function completely independent of each other and are sold together. 

11. They do NOT vent to atmosphere (VTA), thus are emissions and track legal. 

12. No cutting, drilling or permanent modification to the vehicle is required. 

13.The kit can be installed in minutes only and is easily removed for servicing.

14. The PCV catch can runs inline with the PCV (positive crankcase ventilation) valve and retains it's factory function.

15. Shelby GT500 (S197) Catch Can Kit Details:
- Radium Engineering catch cans feature large 10AN ORB ports

-  A 4AN ORB drain port

- 2-step oil separation baffling

- An O-ring sealed dipstick 

16. Kit inclusive of:
-Anodized oil catch cans with integrated condenser and dipstick
-Anodized laser cut Ford S197 specific mounting bracket
-Anodized aluminum -10AN adapter fittings and hose ends
-Enough 5/8" PCV hose for custom applications  
-Stainless steel mounting hardware

Note: 

- Because the Radium catch cans are pressure sealed, they are great for the supercharged applications.

- The crankcase vent catch can runs inline with the crankcase breather port. 

Radium Engineering Dual Catch Can Kit S197 Shelby GT500 Fluid Lock rad20-0329-FL

 

ISR Performance Driveshaft - LS Swap 350Z- T56 - Steel IS-DS-LS350-T56-S

1. This is a high performance 350Z with LS T56 6 Speed Steel Shaft. 

2. This is the ISR one piece driveshaft conversion for the 350Z platform with LS swap kit using the F-body T56 6 speed transmission. 

3. The ISR Performance driveshafts are designed to be the perfect fit for your conversion swap when using the corresponding ISR swap mounts. 

4. The shaft is built using Dana/ Spicer solid high performance u-joints. 

5. This shaft is only guaranteed to fit if using ISR Performance swap components.

6. Will not fit T56 Magnum transmission

ISR Performance Driveshaft - LS Swap 350Z- T56 - Steel IS-DS-LS350-T56-S

 

Brian Crower BC3301 29mm Exhaust Valves Toyota 2JZGTE Lexus 2JZGE

1. BC valves are one piece design with a friction welded Stellite tip for the best possible performance.

2. Every valve is made from premium grade, heat resistant stainless steel material to insure reliability with high boost and/or high rpm applications.

3. The undercut stem above the head area not only reduces overall weight for extended rpm potential, but also significantly improves air/ fuel flow in and out of the combustion chamber. 

4. Every valve is fully machined and features a swirl polished finish under the head.

5. BC valves are made from premium stainless steel, fully machined and swirl polished for ultimate air flow. 

6. Dished head for added weight savings and increased valve control at high rpm. Standard head diameter.

7. Specify Each size you want. Sold as a set, Will also fit 2JZGE(Non-Turbo) Cylinder heads.

Brian Crower BC3301 29mm Exhaust Valves Toyota 2JZGTE Lexus 2JZGE

 

Corsa 06-13 Chevrolet Corvette C6 Z06 7.0L V8 Air Intake cor44108-1

1. This air intake used an advanced PowerCore Filtration Technology to improve efficiency. 

2. It was manufactured by Donaldson with special design channel that directs air to the engine. 

3. Every filter box is engineered to each specific application for low restriction and increased air volume. 

4. The cross-link polyethylene box protects the filter from engine heat, moisture, dust and debris to provide colder air to the engine. 

5. Air ducts are sculpted in such a way to maximize breathing capabilities of your engine. 

6. Larger diameters, unique bends and smooth transitions will give you maximum horsepower you need.

7. Polished lid embossed with the CORSA Performance logo features a high-grade neoprene foam backing for sound insulation that enhances your engine compartment. 

8. Marine-grade stainless steel clamps provide optimal performance with a solid seal that will not loosen or deteriorate. 

9. High performance silicon connectors provide flexibility while maintaining thermal stability.

Corsa 06-13 Chevrolet Corvette C6 Z06 7.0L V8 Air Intake cor44108-1

 

Motorsport Hardware BMW Toyota A90 Supra 82mm Race Wheel stud kit - 14x1.25 5-Lug 8214125-5-BC

1. This is BMW F and G-Chassis Toyota A90 Supra Wheel stud conversion kit - 5-lug 82mm 14x1.25

2. The Kit consists of: (20pcs) Race studs + (20pcs) Standard open black conical nuts

3: A wheel stud conversion kit is perfect for making wheel changes faster and much easier. 

4. The use of spacers are much simpler by eliminating the need to use the correct length lug bolts.

5. Proper installation is torquing the stud to 25ftlbs with blue or orange thread locker, then torquing the nuts to 105ftlbs

6. These high performance studs are just perfect for F and G-Chassis.

7. These studs will save your wheel hub from repeated off-on damage

8. Features:

- 10.9 grade hardness 
- Fast start nut installation
- Wider stud body diameter for increased strength 
- Black Zinc Finish
- Bullet Nose
- Allen Key insert for easy install
- Extended thread design – Will accept up to a 20mm spacer
- Each kit comes complete for your vehicle (4-wheels)
- Fitment BMW F and G Chassis ALL models 2014-present

Motorsport Hardware BMW Toyota A90 Supra 82mm Race Wheel stud kit - 14x1.25 5-Lug 8214125-5-BC

 

Megan Racing Rear Differential Bushing for Scion FR-S & Subaru BRZ MRS-SC-0603

1. Through the years the soft rubber bushings deteriorate after constant flexing and vibration as well as being punished through weathering; this can cause them to tear and may seriously damage your differential and transmission. 

2. Megan Racing has developed a Harden Rubber Reinforced Differential Bushings for Scion FR-S and Subaru BRZ.

3. These reinforced bushings are perfect for enthusiast who is looking to get the most from their vehicle as they will allow more energy to be transferred to the wheels instead of absorbing the energy into the OEM soft rubber.

4. Hardened Rubber utilized is rated at 70A on the durometer scale.

5. Vehicle Fitment
Scion FR-S / Subaru BRZ '13+
Toyota GR 86
Subaru BRZ '22+

Megan Racing Rear Differential Bushing for Scion FR-S & Subaru BRZ MRS-SC-0603

SEEKER SES MUFFLER KIT TRIDENT FOR HONDA CIVIC FK8 11600-FK8-000

 

SEEKER SES MUFFLER KIT TRIDENT FOR HONDA CIVIC FK8 11600-FK8-000

1. This is an extremely high performance exhaust system for maximum power with a genuine ECU or even when boosting up with a tuned ECU. 

2. The exhaust pressure is controlled so as not to sacrifice low speed torque by inserting a slight throttle inside the main silencer. 

3. However during accelerating at full throttle, SEEKER had secured the necessary and sufficient flow rate without sacrificing the superiority of the main pipe 76.3Φ. 

4. Dedicated center pipe for SEEKER SES MUFFLER KIT TRIDENT FOR HONDA CIVIC FK8 11600-FK8-000: Installed silencer x 2 on the main pipe diameter of 76.3Φ 

5. Dedicated tailpiece:
Three out layout = For the purpose of maximizing the exhaust performance while inheriting the genuine design, SEEKER adopted a very costly two-step branching method. 
* 76.3Φ → 60.5Φ × 2 → 60.5Φ × 3 

6. Dedicated finisher:
The finisher is equipped with a powerful 101.6Φ triple finisher. 

7. Adopted a luxurious blue-printed titanium-style slash curl tail. 

8. Each main silencer outlet is manufactured with a special tapered part to control the pulling volume and sound quality when the accelerator is off. 

9. This product is a set of front pipe + intermediate pipe + tail silencer. It cannot be used individually.

10. This SEEKER SES MUFFLER KIT TRIDENT FOR HONDA CIVIC FK8 11600-FK8-000 will surface up FK8 true power potential and improve horsepower accordingly.

SEEKER SES MUFFLER KIT TRIDENT FOR HONDA CIVIC FK8 11600-FK8-000

 

Kansai Service Front Tower Bar for Toyota GR Supra DB KST017

 

Kansai Service Front Tower Bar for Toyota GR Supra DB KST017

1. All GR Supra grades can be installed however Product Specifications are subject to change without notice.

2. This is a high performance tower bar for monocoque protection and increased rigidity with minimal items.

3. The front section is connected with a steel oval shaft in the vertical direction of the upper mount and core support and an aluminum oval shaft is connected in the left-right direction to increase rigidity. 

4. The interior side is remade with a robust φ35 steel shaft, eliminating the genuinely installed square aluminum pipe. 

5. By increasing the number of mounting bolts, stress is dispersed and the monocoque is strengthened and protected for better performance.

6. It can also be used to install a shoulder belt on a racing harness and a bracket is provided in the center so that it can be easily fixed to an onboard video camera. 

7. Material is Steel Oval Shaft: Aluminum Cross Section Oval Shaft φ35 Steel Shaft 

Kansai Service Front Tower Bar for Toyota GR Supra DB KST017

 

Scotidi 79-04 Mustang Drift Spec Control Arm Set 001-005-0098

1. This is a brilliant Minimal Design from Scotidi but with Maximum Angle.

2. This 79-04 Mustang Drift Spec Control Arm Set features few great technicalities:

- Minimum 2.5" over stock length
- Adjustable Length
- Solid mount
- Clearance for 60° steering angle
- Works with Scotidi Quick Angle Kit OR stock spindles (with adapter kit)
- Wrinkle black powdercoat

3. It was indeed a great compliment to have this excellence drift spec control arm kit for your 79-04 Mustang.

FOR TRACK USE ONLY, NOT D.O.T. APPROVED

Scotidi 79-04 Mustang Drift Spec Control Arm Set 001-005-0098

 

Hotchkis Front Heavy Duty End Links for BMW E46 25826F

1. Many E46 BMW 3 Series and M3 owners choose to upgrade their cars with stiffer sway bars. 

2. However without knowing, often this stiffer bar upgrade can cause the factory end links to fail. 

3. Hotchkis Sport Suspension had stepped forward with Sport End Links which use a combination of high articulation rod ends for maximum range of motion and  a quiet, greasable polyurethane bushings for comfort. 

4. These Sport End Links from Hotchkis really make great addition to any BMW sway bar upgrade.

5. Therefore, upgrading stiffer sway bar should be coupled with sturdy end links to avoid any hiccups.

Features:

• Specifically designed for the BMW E46 3 Series and M3's.
• High articulation ball ends for maximum range of motion.
• Height adjustable for optimum fit.
• Range of Adjustment 11" Shortest, 12" Longest. 
  
  Benefits:
• Optimum end link alignment on lowered cars.
• Increased sway bar effectiveness.
• Maximum range of motion.
• Increased end link strength.

Hotchkis Front Heavy Duty End Links for BMW E46 25826F

 

Perrin Battery Tie Down for WRX/STI/BRZ/FR-S/86, Black perPSP-ENG-700BK

1. The PERRIN Battery Tie Down STIFFI is a quick and affordable upgrade. 

2. Keep your battery from moving in all situations.

3. CONSTRUCTION- The PERRIN Performance Battery Tie Down is machined from billet aluminum with radius edges and countersunk mounting holes.

4. FINISH- Available in either black or silver anodizing, the PERRIN battery tie down is an easy way to dress up the engine bay of your Subaru.

5 YEAR WARRANTY

PERRIN Performance warrants to the original purchaser, all PERRIN products to be free from defects in material and workmanship within a sixty (60) months period from the date of purchase. *Some exclusions apply*

IN THE BOX

(1) PERRIN Battery tie Down

Instructions

Stickers

Perrin Battery Tie Down for WRX/STI/BRZ/FR-S/86, Black perPSP-ENG-700BK