HKS Advanced Heritage CFRP Intake System - Nissan GT-R R32 89-94 hks70029-AN001

1. The is the most advance Heritage Concept intake system by HKS for Nissan GT-R R32. Ultimate engineering for the highest efficiency intake system.

2. This is truly unmatched intake system with superior exceptional specifications to note, the best for horsepower improvement projects.

3. The painstaking hard works with state-of-art technology had enable HKS to super fine on efficiency for few crucial parameters. 

4. The hot air intake temperature is reduced by 60%, air filter area by increased by 6% and the pressure lost decreased by 46% when compared to the previous HKS special piping kit. This amazing result shown as below.

5. Features:

- CFRP (Carbon Fiber Reinforced Polymer) is utilized for the primary components, including the piping and air cleaner box, to achieve a weight reduction of approximately 65% compared to the factory intake system. 

-To enhance heat resistance, a high heat resistant prepreg with a temperature resistance of 350 degrees C or higher is used. This is for the chamber pipe after supercharging and the suction pipe near the turbine. They prone to face to high temperatures.

- The cleaner box was specially designed with CFRP, making a great weight reduction. 

- The air filter surface area has also been increased by approximately 6% to improve intake efficiency. The air flow sensor is not a stock component which increases the pipe diameter. 

-The entire layout has been reviewed to achieve higher efficiency and a dedicated washer tank is also included in the kit.

- The enclosed design minimizes the intake of hot air into the engine compartment, resulting in a reduction of up to 60% in intake air temperature during WLTC mode when compared to the exposed HKS Super Power Flow system.

- The pressure loss has been significantly decreased by 46% compared to the previous installation of the HKS special piping kit. 

- This improvement is achieved through an enlarged suction capacity and an increased cross sectional area for introducing outside air. 

-The dual intake ducts allow for approximately 2.4 times more air to enter than the stock system. This enhancement was observed during the 600ps phase.

- An anti surge plate, also known as a surge suppression rectifier plate, has been installed in the suction pipe to address the issue of intake air interference, which has been a persistent problem in the RB26 twin turbo layout. 

- This plate effectively increases the margin for intake air flow, helping to prevent surging and maintaining optimal performance.

- The geometry of the 2 in 1 chamber pipe has been optimized to ensure consistent operating conditions for both the front and rear turbines. This improvement results in a more balanced flow and performance. 

- In comparison to conventional HKS special piping kits, the flow discrepancy between the front and rear turbines has been reduced by an impressive 90%.

6. These are extremely extraordinary specifications achieved by the top achiever, HKS. The HKs Advance Heritage CFRP will bring the “Beast’ Nissan GT-R R32 in an another level. 

HKS Advanced Heritage CFRP Intake System - Nissan GT-R R32 89-94 hks70029-AN001

 

NISMO Cat-Back Street Exhaust - 2023 NISSAN Z RZ34 B0100-RZ34S

1. Nismo Cat-Back was constructed from a high quality T-304 stainless steel and will gives a sporty true tone.

2. The new 2023 Nissan Z RZ34 with a unique retro looks will be more enjoyable to drive even at the back for city drive, comfort without any unwanted noise or drone effect.

3. Significant back pressure reduced means a good horsepower improvement and better performance to excite.

Features:

• T-304 Stainless Steel construction for high strength and corrosion resistance.
• Direct bolt-on application using OEM mounting hanger locations- no modifications required.
• 2.25” pipe outer diameter, with a laser-etched NISMO logo on the exhaust tips.
• Increased exhaust gas flow with 45% reduction in back pressure.
• Sound levels are: 88 dB stationary, 90 dB WOT pass-by, and 68 dB at constant speed.

NISMO Cat-Back Street Exhaust - 2023 NISSAN Z RZ34 B0100-RZ34S

 

BMS JB4 for Ford Mustang 2.3L EcoBoost BMS-JB4-MUS23

1. Power gains of up to 60whp and 100wtq on a factory vehicle without the risks of flashing!

2. The JB4 is a plug and play tuner that attached to two easy to access sensors in the engine bay.

3. It works with your factory ECU tuning to remap your boost, timing, and fuel for an optimal performance and reduced turbo lag.

4. Installation is very discrete and unlike flash remaps, which are quick to install but can never be fully removed with a JB4 the vehicle is never aware it's making more than the factory boost or power levels. 

5. Maintain fuel economy during normal driving after installation.

6. Unlike other less advanced systems, the JB4 includes CANbus functionality allowed it to take in critical engine data directly from the ECU for real-time tuning. 

7. The data includes pedal position, throttle position, timing advance, fuel trims, air/fuel ratio, engine knock, fuel trims, gear, and more. 

8. Other tuners without CANbus are not able to even monitor this critical engine data, no less incorporate it real-time into their tuning algorithms. 

9. CANbus allows the JB4 to provide huge power increases with unparalleled power delivery.

10. JB4 Features & Benefits
• Power gains of up to 60whp and 100wtq on a factory vehicle
• Improves 0-60 times and 1/4 mile times
• Preloaded with custom JB4 Ford tuning software and up to 8 maps for various fuel and modification levels
• Ethanol (E85) compatible tuning maps
• Able to read/delete fault codes
• View and record up to 40 gauges/engine parameters in real-time with the JB4 app.
• Boost by gear in 1st, 2nd, and 3rd can be controlled via the JB4 app for a perfect launch
• Exhaust flap operation can be controlled in most JB4 applications
• Compatible with JB4 Mobile for smartphone logging, tuning changes, and adjustment
• The JB4 offers a lot more performance, functionality, and safety than your average performance chip
• Quick Plug & Play Installation
• CANbus OBDII integration offering unrivaled tuning features and performance
• Improved performance over non-integrated chip tunes
• Runs as smoothly as stock. This is how your vehicle should have come from the factory
• Compatible with all driving modes
• Fuel economy unchanged during normal driving
• 91 octane fuel or better required for performance gains
• Not VIN locked and can be removed without a trace and resold down the road
• Includes the rugged JB4 billet aluminum enclosure for protection
• Made in the USA
• Free USA Shipping
• 5 year warranty

11. Vehicle Fitment
Ford Mustang
• 2015+ Ford Mustang 2.3L EcoBoost turbocharged

12. What is a JB4?
The JB4 is a plug & play tune available for turbocharged vehicles. The JB4 tuner installs between your car's sensors and its DME/ECU (computer) and manipulates vehicle performance through these connections making your vehicle much faster. While it's not the only tuning system that operates this way, the JB4 separates itself from the competition with much more advanced connection points and processing, including CANbus, fuel & spark control, Bluetooth to your smartphone, and a variety of innovative and advanced features not possible with any other system. BMS regularly publishes free mapping and firmware updates adding performance and features as ongoing development allows. In addition, the JB4 system is not VIN-locked to your vehicle and can quickly be removed and swapped between cars or resold at a later time. Often imitated but never duplicated the JB4 has been the gold standard in plug and play turbocharged performance tuning for over a decade.

BMS JB4 for Ford Mustang 2.3L EcoBoost BMS-JB4-MUS23

 

Scion FR-S & Subaru BRZ ARK DT-S Exhaust System 

1. The DT-Series premium exhaust gives the perfect combination of sound, style and performance. 

2. The ARK DT-S premium exhaust has been carefully engineered and manufactured to ensure 100% satisfaction. A great horsepower improvement exhaust from ARK.

3. The overall quality of DT-S exhaust is unmatched in term of mandrel bends, flawless welds with T304 SS material. 

4. The DT-S exhaust is designed with tone control and multi-layer sound compression materials to provide the perfect pitch you are seeking. 

5. This exhaust not only provides great tone, but also is dyno proven to maximize performance and engine response. 

6. The DT-S exhaust comes in many premium tip finishes such as polished, burnt, and tecno. With all the different exhausts in the market, the DT-S premium exhaust stands out beyond the rest. 

7. The flawless manufacturing, perfect pitch, and clean style makes the premium DT-S exhaust the perfect choice for Scion FR-S and Subaru BRZ enthusiast. 

ARK Advantages and Features: 
- All Bolt-on System 
- Burnt Tips 
- SUS304 Stainless Steel Construction 
- Fully Polished Finish Piping 
- CNC Machined Flanges 
- Exposed Micro TIG Welded 
- Signature ARK Reservoir Design to reduce drone 

Scion FR-S & Subaru BRZ ARK DT-S Exhaust System 

BMW F Chassis BMS Differential Support Bracket Brace- Large Diff BMS-DB-F-L

1. The BMS differential brace attaches the rear differential to the subframe.

2. This will allow for better launches, less wheel hop and a more stable feeling rear chassis. 

3. BMS unique one-piece construction eliminates welding weak points common on similar units. 

4. No logos or markings are visible for a stealth OEM appearance. 

5. Please Note: Drilling is required. 

FEATURES AND BENEFITS
• Tightens chassis
• Reduces wheel hop
• Reduces differential bearing load
• All hardware included
• Precision made one-piece design for a perfect fit
• Heavy-gauge steel construction for maximum strength and durability
• Easy install
• Made in the USA

6. Vehicle Fitment
• Large - 2016+ 1/2/3/4 F series BMW- Rear wheel drive only

7. Not compatible with M2 comp, M3, M4. 

BMW F Chassis BMS Differential Support Bracket Brace- Large Diff BMS-DB-F-L

 

BMW N54 25WHP increase with 2” Turbo Outlets ARM Motorsports N54OUT

1. The ARM N54 Turbo Outlets will increase horsepower on your N54 BMW by improving airflow post-turbo. 

2. The specific section of piping is enlarged on the ARM N54 outlets to 2". This will increase 100% capacity over the stock outlet size of 1". 

3. This section of piping is critical as it is the first component of the charge-air system.

4. Specifications:

- 2" Aluminum Construction

- Gain Up to 25whp
- Improved Low-End Torque
- T6061 Aluminum

5. The ARM Motorsports BMW N54 Turbo Outlets utilized T6061 aluminum for durability and long life. 

6. Uses an enlarged OEM-style CNC machined V-band connection at the turbo for an easy installation that will connect to any OEM-style or upgraded turbos using the 2" OEM connection.  

7. The OEM N54 Outlets use a divorced piping design which separates the two channels of air coming from each turbo. 

8. The ARM N54 Turbo Outlets improve airflow by merging the charged air from each turbo upstream, allowing them to combine before entering the FMIC.

9. Joining the two sections of the ARM N54 Outlets with a 5-layer silicone coupler designed to prevent expansion on high-boost applications. 

10. Securing the silicone coupler are two T-bolt clamps to ensure a solid connection that will not leak or come loose over time.

11. IN THE BOX
- ARM N54 Turbo Outlets
- 2x O-rings
- 1x Silicone Coupler
- 2x Clamps

**FITMENT GUIDE:
DOES NOT FIT RIGHT-HAND-DRIVE VEHICLES

12. There are various BMW N54 models that may benefit from this great horsepower improvement turbo outlet from ARM Motorsports.

**Make Chassis Model Engine that compatible with ARM Motorsports turbo outlets:

BMW E82 1 M Coupe N54 3.0L
BMW E82 135i N54 3.0L
BMW E88 135i N54 3.0L
BMW E90 335i N54 3.0L
BMW E90 335xi N54 3.0L
BMW E92 335i N54 3.0L
BMW E92 335is N54 3.0L
BMW E92 335xi N54 3.0L
BMW E93 335i N54 3.0L
BMW E93 335is N54 3.0L
BMW E60 535i N54 3.0L
BMW E61 535i N54 3.0L
BMW E60 535xi N54 3.0L
BMW E61 535xi N54 3.0L
BMW Z4 sDrive35i N54 3.0L
BMW Z4 sDrive35is N54 3.0L 

13. ARM MOTORSPORTS LIFETIME WARRANTY. Every ARM Motorsports product is backed by a lifetime warranty which is automatically issued at the time of purchase. 

**Your warranty protects you against any defects in craftsmanship or fitment. The warranty entitles you to a replacement unit.

BMW N54 25WHP increase with 2” Turbo Outlets ARM Motorsports N54OUT

 

Mustang GT ‘15-‘16 C&R Auto Trans Cooler CR43-00000

1. This is a new High Performance Transmission Oil Cooler for the 2015-16 Mustang GT.

2. Engineered to lower transmission temperature especially when horsepower and torque is increased. 

3. All are bolts-in, same as factory and all are made from aluminum. 

4.Uses PWR core and made in the US.

Mustang GT ‘15-‘16 C&R Auto Trans Cooler CR43-00000

 

Ford Mustang GT '15-'18 Whiteline Adjustable Toe Arms KTA228

1. This is an ‘Activate More Grip’ with adjustable, a heavy-duty Rear Toe Arms for your Mustang GT.

2. A unique engineered synthetic elastomer bushings from Whiteline is an easy to install control arms to note. 

3. This is a must-have for all lowered 6th generation Mustangs, as they allow adjustment of the rear toe to optimize geometry of your cars’ rear end after lowering. 

4. Even if your Mustang is not lowered, Whiteline’s aftermarket Rear Toe Arms give you the adjustability to fine tune your suspension, which improves overall handling and performance.

Ford Mustang GT '15-'18 Whiteline Adjustable Toe Arms KTA228

 

Mustang 05-14 RTR Tactical Performance Coilovers 11081.0001.11.A

1. The RTR Tactical Performance Coilovers will improve steer and handling capability. Absolutely will redefine your S197,GT and Boss 302 performance. 

2. It will give a perfect balance between aggressive/ sporty driving and comfort.

• Fits 2005-2014 S197 Mustang V6, GT and Boss 302
• DOES NOT FIT: Shelby GT500 and GT500KR
• Lowers your Mustang 1.5-inch Front and Rear
• RTR Tuned Valving
• Mono-Tube Shock Design - Nitrogen Filled
• Separate Ride Height and Preload Adjustability
• Adjustable Piston and Damping Curve
• Utilizes OEM Top Plate and Bearing for reduced NVH
• 30-Clicks of Simultaneous Compression/Rebound Adjustment
• Custom Spring Rates - 6 kg/mm (Front) 4kg/mm (Rear)
• Height Adjustment Independent of Spring Compression
• Includes Spanner Wrenches
• 1-Year Warranty Against Manufacturers Defect
• Fully Rebuildable

What's in the Box:
• (2) Front Strut Assemblies
• (2) Rear Shocks
• (2) Rear Springs
• (4) Spanner Wrenches
• Front Endlinks Included

Installation Time: (approx.) 5 Hours
Difficulty Level: Mechanical expertise or professional installation required

Mustang 05-14 RTR Tactical Performance Coilovers 11081.0001.11.A

 

APR Performance GT-250 Carbon Fiber Wing for Lamborghini Galardo 2013-2013 aprAS-207101

1. All GT Series wings feature an all-new, low-drag, aerodynamic 2D designed airfoil shape. 

2. The "2D" design allows the wing to maintain a consistent level of downforce across its entire span. 

3. Computational Fluid Dynamics (CFD) analysis was performed on this wing to support validation of its aerodynamic design. 

4. Each GT Series airfoil is composed of lightweight and durable carbon fiber reinforced polymer (CFRP) composite materials. 

5. These airfoils contain pre-pregnated woven carbon fiber sheets for superior strength and low weight. 

6. All CFRP airfoils are made using pre-pregnated composite manufacturing processes (i.e. high-temperature autoclave and vacuum bagging) in high-quality aluminum billet molds.

7. Gurney flaps are included and pre-installed with every GT-250 wing. These are super lightweight, made using pre-pregnated carbon fiber processes.

APR Performance GT-250 Carbon Fiber Wing for Lamborghini Galardo 2013-2013 aprAS-207101

 

ARMYTRIX Titanium Valvetronic Exhaust System Matte Black Tips Lamborghini Gallardo 2008-2013 LBGL5-QT17M

1. ARMYTRIX gives an ultimate lightweight "aero-grade" titanium exhaust for the best performance and exhaust sounds upgrades for the best supercars.   

2. ARMYTRIX spent hundreds of hours of development and tuning to unlock the perfect combination of exhaust tone, sound volume and practicality. 

3. The exhaust system had unlocked the power hidden in the V10 engine and produce a much more aggressive and refined exhaust sound. 

4. Much lighter with 21kg less than OEM for this Gallardo system. 

5. ARMYTRIX used aero-grade titanium throughout the entire system for an unmatched performance. 

6. ARMYTRIX exhaust systems differ from other brand' exhaust systems with their unique "Throttle Pedal Sensor and Engine RPM Signal Auto Functions". 

7. When your car at high speeds, the valves will automatically open to increase air flow for better performance (HP & torque gained) and sound. 

8. This is a great innovative system that brings your car to a different level with a significant horsepower improvement and more aggressive sound to note.

Includes:

• Valvetronic Mufflers
• Quad Tail Pipe
• Remote Control Module

Features:

• LP550-2 | 560-4 | 570-4
• Power ( HP): 21.7
• Torque ( Nm): 22.7
• Weight Saving (-Kg): 18.5
• View Install Instructions Here.

Fitment:

• Lamborghini Gallardo LP560-4 2008-2013
• Lamborghini Gallardo LP550-2 2010-2013
• Lamborghini Gallardo LP570-4 2010-2013

Notes:

• ARMYTRIX wireless valvetronic wiring is a plug-and-play system, no cutting, alteration or damage will be done to the factory settings.

ARMYTRIX Titanium Valvetronic Exhaust System Matte Black Tips Lamborghini Gallardo 2008-2013 LBGL5-QT17M

 

Tomei Full Titanium Front Pipe Kit for Nissan RB26DETT TB6080-NS05A

1. TOMEI Titanium Front Pipe will optimize exhaust flow especially at high RPM range by the best pipe layout BUT keep the ground clearance. This is common issue with RB26 aftermarket front pipes in the market. 

2. High quality and high strength titanium material allows not just the thinnest wall structure and amazing weight reduction BUT also great durability.

3. The all titanium front pipe gives a significant improvement on horsepower especially for vehicles with the factory stock.

Tomei Full Titanium Front Pipe Kit for RB26DETT TB6080-NS05A

 

REVEL Medallion Touring-S Exhaust for Subaru WRX '22+ T70206R

1. The Revel Medallion Touring-S exhaust system is constructed from full SUS304 stainless steel for corrosion resistance & durability. The1.5mm wall thickness piping is for strength and to reduce resonation. 

2. Mandrel bent process- to retain the same piping diameter at the bends and optimize exhaust flow characteristics. This will be great for horsepower improvementz

3. When testing under 93db sound levels under load, the Medallion Touring-S exhaust system gives a clean & deep tone at all RPM ranges while maintaining exhaust efficiency.

4. The Medallion Touring-S exhaust system is fully hand TIG welded and utilize laser cut flanges that are stronger for more durable connections.

5. The dual-wall angle cut tips have a large inner diameter for modern aesthetics and increased exit flow.

6. Advantex packing material offers superior flow characteristics while offering great sound suppression. 

7. It is heat resistant up to 1200º F and extends the functional life of the exhaust system.

8. Straight through muffler design gives better flow for increased power and allows for a lighter weight system with an aggressive tone. 

REVEL Medallion Touring-S Exhaust for Subaru WRX '22+ T70206R